Skip to main content ↑ ↓
Topic: Artix-plasma ISO cannot be booted properly  (Read 926 times) previous topic - next topic
0 Members and 3 Guests are viewing this topic.

Artix-plasma ISO cannot be booted properly

Hi there,

Just tried booting from official and latest weekly ISO images, but Plasma wouldn’t start properly. Traditional PDF-instructions and a readme file are only downloaded on the desktop, with plasma panels being unavailable. So, I cannot proceed further with the installation because of DE not working.

I tried different ISO images (dinit, S6) with different usb sticks. All was the same.

Re: Artix-plasma ISO cannot be booted properly

Reply #2 –
I’m using Dell Vostro 14 5410-4619. Some January’s images used to work perfectly.

Re: Artix-plasma ISO cannot be booted properly

Reply #3 –
I had been able to run a live session until recently. Couldn’t figure out what happened.
 

Re: Artix-plasma ISO cannot be booted properly

Reply #4 –
Just tested plasma-s6-230401 on my laptop (Dell Precision M4800) and in a VM, it works fine. Perhaps if you switch to console and take a look at ~/.xsession-errors and dmesg, you may find something informative.

Re: Artix-plasma ISO cannot be booted properly

Reply #5 –
Is the mouse not functional?
I ask because the 'Install Artix' icon is there so you may still be able to proceed.

On my system CTRL-ALT-T starts konsole.
Also if krunner is active ALT-F2 then type konsole, hit enter.

Then in konsole
Code: [Select]
plasmashell &
and you may get the taskbar etc. If not there may be useful error messages ?

Re: Artix-plasma ISO cannot be booted properly

Reply #6 –
I cannot perform any actions with the mouse, “instal Artix” is not responding if I’m clicking on it.

When tried running “plasmashell &” via terminal, I got the following:

“qt.gpa.xcb: could not connect to display qt.gpa.plugin: Could not load the Qt platform plugin "cb" in "' even though it was found

This application failed to start because no Qt platform plugin could be initialized. Reinstalling the application may fix this problen.
Available platform plugins are: eglfs, linuxfb, minimal, minimaleg1, offscreen, unc, wayland-eg1, wayland, wayland-xcomposite-eg1, wayland-xcomposite-gix, xb.”

Very odd behaviour. It’s never happened before. All images would normally work well.

Re: Artix-plasma ISO cannot be booted properly

Reply #7 –
Yeah sounds odd.

If you still have am older image you could install from that. After an update things should be the same as if you you installed from the current images

I just tested artix-plasma-openrc-20230401-x86_64.iso in a VM and it's working fine.

If you refuse to go down without a fight here's the command that starts the installer
Code: [Select]
su
env DISPLAY=:0 XAUTHORITY=/home/artix/.Xauthority QT_QPA_PLATFORMTHEME=gtk2 calamares
I navigated a few pages deep with just the keyboard (Arrows, TAB and Space)

Re: Artix-plasma ISO cannot be booted properly

Reply #8 –
I’ve got two more images from 31.03.2023 and 15.02.2023. All was the same. Can’t understand what’s gone wrong.

Base ISO works as intended and allows to perform the full installation, but sometimes I need to use a live session. I first thought that some of my hardware had broken down, but there were no hardware issues when tested. I can run other distributions in live mode without any problems, but I’m used to Artix with S6 onboard.

I’m determined to find out what has caused the issue.

Re: Artix-plasma ISO cannot be booted properly

Reply #10 –
Quote from: nous – on
Quote from: Anthony – on
I’ve got two more images from 31.03.2023 and 15.02.2023. All was the same. Can’t understand what’s gone wrong.
NVidia GPU? Try disabling nvidia module loading at boot or disabling KMS.



My Dell is equipped with Intel GPU only. It shipped with Ubuntu pre-installed. I bought it specifically for Linux.

Re: Artix-plasma ISO cannot be booted properly

Reply #11 –
What is installed on the laptop atm ?

Re: Artix-plasma ISO cannot be booted properly

Reply #12 –
I had to install EndeavourOS. I might as well take a base Artix ISO and perform the installation, but sometimes I need to boot into a live session. It’s quite convenient when you can open up your own manual with the selected commands being written down in advance. It allows to reduce installation time substantially.

UPD: I’ve got one more old Lenovo laptop and Artix-plasma ISO works well on it. It looks like something is wrong with my Dell, but if it were a hardware failure I wouldn’t have been able to boot into live sessions of any kind of distros.

Re: Artix-plasma ISO cannot be booted properly

Reply #13 –
Quote from: Anthony – on
It looks like something is wrong with my Dell,
I wouldn't have thought so.
Probably drivers.
If you don't mind would you humour me and post the output of
Code: [Select]
lspci -k
for both the working installed system and the non working iso.

Edit if you have to do pictures of the iso's output no worries.
And the same if you really can't be bothered ;)

Re: Artix-plasma ISO cannot be booted properly

Reply #14 –
Here’s my output from the iso. It’s the same for the working system.